Seismic load calculation for Pressure Vessel (ASCE 7-10) 1. Site Class Soil property 에 따라 Site class A,B,C,D,E or F 로 구분되며 일반적으로 Project spec 에 명기되어 있음. 특별한 명기가 없다면 Class D 를 사용 할 것. Site Class 에 따라 Fa (short period site coefficient), Fv (long-period site coefficient) 값이 달라짐. 즉 지반이 무를수록 지진파는 증폭된다. Class A: Hard Rock Class B: Rock Class C: Very dense soil and soft rock Class D: Stiff soil Class E..
Bolt Hydraulic tensioner 란? (ft. 유압계산방법) 1. Hydraulic Bolt Tensioner 란? - large bolt (일반적으로 1-1/2” 이상) 설치 시 정확한 bolt tension 을 유지하기 위하여 유압을 사용한 hydraulic bolt tensioner 를 사용한다. - 기존의 manual torque ranch 와는 달리 nut 를 강조로 조임으로써 bolt 를 인장시켜 tension 을 주는 것이 아니라 유압을 사용한 annular jack 을 이용하여 Bolt 를 들어올리고 nut 를 조여주는 방식 - Bolt 의 길이는 tool 을 설치하여 물릴 수 있도록 일반적으로 1 nut 이상의 길이가 추가로 확보되어야 한다. - Bolt 의 간격은 tool ..
Column Tray Internal Part 종류 1. Tray Internal part (1) Tray Deck (Tray Floor) Liquid 와 Vapor 가 Cross Flow 로 서로 접촉하여 Mass Transfer 가 일어나는 부분과 Downcomer Inlet Area 로 구성되어 있다. (2) Downcomer Tray Deck 을 통과한 Liquid 를 아랫단의 Tray Deck 로 보내기 위한 통로이고 Tray 의 Performance 에 따라 아래 그림과 같은 여러가지 Type 으로 분류된다. (3) Outlet Weir Tray Deck 에서 Downcomer 로 떨어지는 Liquid 를 정체시켜 Contact Time 을 늘리는 역할을 하는 것으로 Tray 의 Pressur..
[Shell & Tube Exchanger] Pulling bundle Calculation (API 660 & TEMA) 1. API 660 Para 7.3.1 Shell Supports When the support of a removable-bundle heat exchanger is fixed to the shell, it shall be designed to withstand a longitudinal force equal to 150 % of the bundle mass applied at the heat exchanger bundle centerline. The shear stress for supports shall not exceed 40 % of the yield strength of ..
[Shell and Tube Heat Exchanger] Strength weld tube to tubesheet joint requirement (API660 & TEMA & ASME) 다음과 같은 condition 이 적용될 경우 strength welded tube-to-tubesheet joint 를 적용한다. 1. API 660 Para. A.4.4.3 Strength-welded tube-to-tubesheet joints should be considered by the purchaser for the following conditions. a) Design Pressure > 7000 kPa b) Duplex stainless steel tubes in wet hydrogen sulfide..
[Shell and tube heat exchanger] Collar bolt application for extended tubesheet (API 660 & ASME) 1. API 660 para. 7.5.2.1 For a vertical heat exchanger where the stationary tubesheet is at the bottom, a suitable means of holding the tube bundle in place shall be provided for when the bonnet or channel is removed. If collar bolts or drilled-and- tapped holes are used, at least four shall be provid..
[S&T Heat Exchanger] Pass partition plate 두께 산출 (API 660 & TEMA) 1. TEMA RCB-9.1.3.1 The thickness of pass partitions shall not be less than the greater of that shown in Table RCB-9.1.3.1 or calculated in Paragraph RCB-9.1.3.2. Pass partition plate 는 아래 table 의 값을 minimum 으로 사용하고 계산식에 의하여 두께를 결정한다. 2. TEMA RCB-1.5.1.8 Pass partition plates and welded in long baffles Pass partition plates and wel..
엔지니어링 관련 블로그를 쓰면서 머리속을 정리하기 위해서 최대한 간단히 쉽게 기술하고자 한다. 이번에는 Desalter 의 원리 및 구성품에 대하여 간단히 정리하고 자세한 내용은 시간이 나면 나중에 기술해야지.. 1. Desalter 원리 Desalter 는 원유 중의 염분을 제거하기 위한 장치이며 보통 정제시설 도입부에 주로 설치되는 탈염설비이다. 원유 속에는 염분 즉 Chloride 가 상당량 포함되어 있고 chloride 는 금속의 부식이나 촉매의 독으로 작용하기 때문에 후속 Process 전에 제거하는 것을 목적으로 한다. 제거하지 않으면 Carbon steel 의 경우 Chloride 성분 때문에 pitting corrosion 이나 Stainless 는 Chloride stress corros..
Lamellar Tearing - 열간 압연에 의해 생산되는 강재는 압연이 진행되는 방향의 단면과 교차되는 단면의 서로 다른 기계적 성질을 갖음 - 교차되는 단면의 연성 ductility 가 압연진행방향에 비해 떨어짐 - 얇은 판에 수직 하중이 작용하면 변형의 집중현상과 적은 연성능력으로 취성파괴 발생 - 주 원인은 용접후에 부재에 일어나는 수축현상과 Mn, H 집적, 불순물 편석등 Z quality - 보통 rolling direction or width 방향으로만 mechanical property 표기 - thickness 방향 (z direction) 으로 시편을 따서 tensile test 실시 - Z15,25,35 는 reduction of area 를 % 로 표기하는 숫자 => Raz = (..
1. High Temperature Hydrogen Attack (HTHA) High Temperature Hydrogen Attack (HTHA) 는 고온과 수소 환경에서 운전될 때 carbon 과 low alloy steel 의 성능을 저하 시킬 수 있다. Hydroprocessors, hydrotreaters, naphtha hydrotreaters, catalytic reformers, and hydrogen manufacturing plants 는 HTHA 에 노출되어 있는 process 이다. Hydrogen attack 은 수소 원자가 존재하여야 한다. 수소 원자는 보통 낮은 온도에서 불안정하여 두개의 수소원자는 수소 분자로 자발적으로 결합한다. 하지만 높은 온도에서는 수소 분자는 다시 일정..
1. Shell & Tube Heat Exchanger rear head type - 일반적으로 thermal expansion 및 cleaning 을 고려하여 rear end head type 을 S, T type 으로 설계함 - shell 과 tube side 의 temperature difference 에 의한 expansion 을 고려할 필요가 없으며 bundle 을 분리 할 수 있어 full mechanical cleaning 가능 - “T” type 의 경우 shell 을 크게 만들어 bundle 을 별도의 분리 작업없이 통째로 removal 가능 - “S” type 의 경우 backing device (split ring) 체결로 인하여 floating head flange 가 shell I..
1. Wind Code - Pressure vessel 의 wind 계산은 ASCE / IBC / UBC code 에 따라 계산한다. - 일반적으로 ASCE 7 (American Society of Civil Engineers ) 을 적용하며 7-5, 7-10, 7-16 edition 은 project spec 에 따라 선택 적용 한다. 1) Cf : Wind force coefficient - shape factor 로써 flat 보다 round 가 wind pressure 를 덜 받게 되니 force 계산시 적용 - Vessel 의 경우 일반적으로 0.8 적용 - 아니면 h/D 를 이용하여 보간법으로 산출 2) Basic Wind Speed - 해당 지역의 basic wind speed map 에 따..